Menu
Home
Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Members
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Current visitors
New profile posts
Search profile posts
Search
Search titles only
By:
Search titles only
By:
Menu
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
glacierbaze's latest activity
G
glacierbaze
reacted to
Capt Tom's post
in the thread
Hard Top vs Bimini for Freedom 235
with
Like
.
Hardtop with curtains, that's what makes these DC's superior to CC's IMO. Don't always have fair seas and nice weather out on the water.
May 4, 2024
G
glacierbaze
reacted to
luckydude's post
in the thread
Pulling the trigger on a pilot house on the 228
with
Like
.
Yeah, Charlie (the fabricator) wasn't sure about that when I asked for it but once he finished he told me "I should have done this on...
May 3, 2024
G
glacierbaze
reacted to
Fishtales's post
in the thread
Bolster and Seat Recover
with
Like
.
Started the companion seat. Bottom seat patterned and sewed, looks fine. Gluing the foam to the curved back (inside and out) is a bit...
Apr 29, 2024
G
glacierbaze
replied to the thread
Steering wheel removal
.
If it is original equipment, the nut should match the shaft, and it will be a heavy duty one piece threaded nut. If it is a replacement...
Apr 29, 2024
G
glacierbaze
replied to the thread
Starting
.
I missed that you were reconnecting the battery. As said, probably left off a ground wire, since there are usually more black than red...
Apr 29, 2024
G
glacierbaze
replied to the thread
Steering wheel removal
.
Is that an Edson wheel? If it was just a cover nut for the “real nut“ it would pop off rather than unscrew. I believe it has an insert...
Apr 29, 2024
G
glacierbaze
replied to the thread
Starting
.
Is the tilt trim also dead? Check the fuse under the engine cowling. There is usually a spare.
Apr 29, 2024
G
glacierbaze
reacted to
Fishtales's post
in the thread
ACR PLB vs InReach Mini
with
Like
.
to be honest I cannot remember. The EPIRB is prob 1/2 the cost of a new one. The PLB, was a custom battery. I took it apart and...
Apr 25, 2024
G
glacierbaze
reacted to
SkunkBoat's post
in the thread
ACR PLB vs InReach Mini
with
Like
.
You can change them youself. Just buy the battery pack that is already made...
Apr 25, 2024
G
glacierbaze
replied to the thread
Anyone have or know where to find bow table pole?
.
If you have an ebay account, click on it a few times, and you will get an auto-generated offer from the seller for $500.
Apr 22, 2024
G
glacierbaze
replied to the thread
12V Feed For 2000 Seafarer E-Box?
.
Thanks, I will see it again in a couple if days.
Apr 22, 2024
G
glacierbaze
replied to the thread
Anyone have or know where to find bow table pole?
.
Not mine, on ebay for $550. Yes it is Norsap...
Apr 22, 2024
G
glacierbaze
posted the thread
12V Feed For 2000 Seafarer E-Box?
in
General Discussion
.
I had assumed that the power for the fuse panel in my E box, came up through the pipe from the top of the dash to the side of the box...
Apr 22, 2024
G
glacierbaze
replied to the thread
Anyone have or know where to find bow table pole?
.
Did GW tell you the manufacturer? Your picture gets fuzzy when enlarged.
Apr 22, 2024
G
glacierbaze
replied to the thread
2017 F250 with new tach gauges ?
.
Swapping gauges may fix any bad connection in the port tach, so if they both work, just go with it.
Apr 18, 2024
Home
Members