Search results for query: newwire

...On/Off/On, MOM ON..... There are Indicator and there are Illuminated and there are illuminated indicator....and even backlit.... Look at the NewWire site. Get an idea of style. Get an understanding of which style and type of switch you need. Contura rockers of all types are availabe at any...

NewWire Marine in Charleston. Several styles available. Change them all out while you are at it. Your old switches are no longer available.

8612 at helm with NewWire gauge panel. 8610 in overhead box. NewWire Switches

...screen resolution than 1243xsv. Can't see if you have an overhead box but you could put the radio there. Alternative is to ditch the cup holder and put radio there. You can put the cup holders on the tower somewhere. Consider NewWire Marine to upgrade switch panel look. Same with gauge panel.

...gauges. I would have to re-sculpture the dash. Run the engines on the Garmin's. Lower panel and switch panel were replaced this summer with NewWire carbon fiber look panels. I really like the idea of a 4k display. It really makes the combo screens work so much better. Eventually I'll get there.

...pins (2 & 5). If it runs the wrong way flip the pins. Wiring on either side reverses polarity (1 to 6 to +12vdc)(4 to 3 to ground). Two top pins (7 & 8) are backlight. Look at NewWire marine web site for switch types and pin assignment...

...mine are set in a "frame" mounting panel from Carlon. It hold the stray light in better and doesn't splash light all over the dash. NewWire sells all this. It was a project to have them build it this way but it turned out good. I went with the low-light red illumination. I don't find it too...

NewWire panels came in today. They look good! This weekends project.

I just went thru this with my boat. I ordered a NewWire Marine gauge and switch panels arriving tomorrow. You will have to snip wire ties. Organize the wires in your hand by gauge and take a photo. Do each gauge. I would use a label maker and carefully mark everything before you take it apart...

...separate illumination for Up and down positions. That will throw some confusion into the mix. There are jumpers for Illumination also. NewWire has a diagram https://newwiremarine.com/wp-content/uploads/2018/07/DPDT-switch-powering-two-loads.pdf I have this switch for my Livewell...

Thanks for the Dremel tip. As I'm assembling and putting ends on, I'll be using corrosion guard on all connections, it's messy, but piece of mind. I've got a little over $1100 in my panel as a reference to your quote, which includes the back-lit Grady-White logo, which of course is extra.

...the connectors and re-use the harness. By the way I found a way to cleanup the wires where the water has wicked in under the insulation. If they are not too bad a Dremel tool with a wire brush and clean them up. May help you with your splicing. I have everything out to Newwire for a quote.

...life span. On my Venture 34 i replaced al rocker switches with toggle switches with a cable instead of spade connectors. The two side panels where made by NewWire and they did a great job, they make either the panel only or with all switches installed and labeled, including custom signs. Chris

Newwire for new panels. https://www.greatgrady.com/search/1796858/?q=newwire&o=date

On my 2007 330 I replaced Garmin 5212s with slightly different sized 1243xsv MFDs. Ordered custom bezels from NewWire marine. Plug and play with a little cutting of existing holes. Existing holes were too small in horizontal dimension and too large in vertical dimension. Very easy! No need to...

Looks great, thanks!

I did have to add trim panels as I remember one of the dimensions of the 1243 was less than the 5212. I had them made by Newwire Marine. They have all the dimensions and provide trim panels for most MFD’s. This picture is not great but I can give you an idea. I added the GT 56 transducer...

...cover. It doesn't have the light at the bottom. We don't know if it is a non-backlit Contura11 switch or if it is the wrong style cover. Don't mix covers and switches up. Verify what you have and what you can use. Read stuff on the newwire site. This is a description on newwire site

Get your replacements from Newwire Marine on line. They provide custom rocker switches in a variety of options and the tool and directions as to how to easily replace the rocker itself. If you pull the panel and the switches look good on the back you probably don’t have to change the switch just...

thank you for the info maybe two 10 inch would be easier and I can put the extra money I save towards auto pilot. I will look into NewWire Marine and get price