Search results for query: sealant

Just picked up a 2021 express 330. no bottom paint. I am in freshwater, northern lake huron. The water is pretty clean here. Not interested in the usual bottom paint look. what are my other choices?

I am replacing the deck winch switches on my 307. What is the best bedding sealant to use for this? Back in my sailing days, we used silicone sealants to bed winches, etc. to the deck. Is 4200 the recommended product for this? Thanks.

...is set to ship tomorrow to the dealership. One of the options they are offering, just like a car dealership would, is a Vantage protection sealant. Supposedly you don't need to wax the boat for five years. The cost is $1600 and they do the interior and the exterior of the boat including the...

I noticed that the sealant between the swim platform and the transom on my Tournament 225 is starting to crack. Do I need to remove the entire platform or can I just pull out the old sealant and shoot some new sealant in? Any recommendations for sealant?

which caulk or sealant to use around that aluminum bang plate and the two plastic corner pieces on the transom ? Any success with a particular product ? many thanks

After removing the center piece of my deck in a 282 what’s the best sealant/caulking to fill in the gap between stationary deck and removable deck price?

...the but the transom is good so for now I'm going to go with just a replacement instead of glassing it over. I've read of all different makes sealant used to seal this, some say 5200, others say 4200, yet others Boatlife caulk. Looking fro some guidance as to what is the best product to use...

Good morning. One of the cupholders in the back of my Fisherman 216 jarred loose (my fault) and it is held in by just a clear sealant. I am sure that water will leak in to the interior/bilge. Until now my bilge is dry as a bone. I need to reseal it. What should I use? Thanks

What is the difference? Are they interchangeable? Deck hatch vs. below waterline through hull opening for transducer install (~1" hole).

Installing new trailer steps that only were available in white. While they look clean today, in a very short period they will look like crap I imagine. Any suggestions on some kind of surface preparation/protectant that will make them at least cleanable down the road?

Was looking for a a source for tubes of 5200 sealant, assume white will be fine. I am referring to the 10oz, I believe. Everywhere I look, the biggest complaint is the lack of a "spout"(?), so have not ordered any. Lowes only has a small 3oz tube, Academy has a little larger, but very much...

I need to reseal my deck plates, the one covering the fuel tanks an the rear one on my 265 . What is the best sealant for this

I have 1995 192. transom seems very solid but I would like to reseal around the transom cap. what should I use? question 2 is one of the drains in the spashwell is worn out it has tranducer cables ran threw it and I guess that what worn it out. the other is fine. it looks like a brass fitting...

Hi - I was just looking at the fiberglass transom cap on my 1994 Sailfish and noticed a gap running along the whole length of the bottom - what should that be sealed with? The top photo is upside down so that the gap that I am talking about is visible. The bottom photo is the same area but...

...unidentifiable clear caulking. For all I know, it could have been factory. Anyway, when we get the replacement hatch back (and have cleaned out the tank compartment, etc.), should we be re-sealing the hatch? If so, does anyone have a recommendation as to the specific caulk/sealant to use for...

...piece to do the work ( not the circular access hatch, but the entire deck panel the hatch is apart of. I am wondering what is the most ideal sealant to use seal the edge when I am finished? I know I do not want 5200 because I might have to access the area again. I have some 4200, but is that...

I replaced my fuel tank this past winter and installed a WEMA sender. Took the boat out yesterday and as soon as the bow went up I smelled gas. Popped the inspection plate over the sender and it was wet with gas. Any recomendations on some type of sealer?

I'm wondering what one would use to seal back up the cracks (the word 'crack' is really a poor word for the space between the panel and the space it fits in) in the floor panels after you remove them, and place them back. Obviously I'm not talking about the round access hatches, rather the...

Is anyone know , what kind of sealant should I used after relocated motor height for mounting bolt? What is the best way to apply sealant when pushing the bolt in?

I'm going to be removing an aft hatch cover on my Tournament 225 to install a raw water washdown. Any advice on the sealant to use when I reinstall this hatch cover. Should I use 5200 or a high quality silicon sealant?