Search results for query: dome light

...then the install. Top was like 9800 delivered (1600 of it was the shipping)... and comes with LED spreader lights, 9 rockets, elec box.. dome light.. all that stuff. Says it takes like 6 men to lift it onto the boat... then drilling holes etc. I will document all mine when it arrives so...

...is something you do not want to add after the fact he stated heh) -- The storage bag -- 2 more rockets down each side (4 total) -- LED Dome light -- LED Anchor light -- The fuse panel/wiring harness to tie it all in -- They are adding a 2nd electrical run to accommodate the extra electronics...

Can you give some more info on mounting the light to a rod holder? Thanks

It takes some calculations to get the proper height and tilt. I attached a pdf showing what I did for a Marlin 300. Note that just clearing the light is not enough. The radar beam has a vertical spread. You will be blocking the lower part of the beam unless the dome is higher. The Marlin...

The blue LED cockpit lighting is so cool, then add the red dome light . . .

Hi all, The dome light in my aft cabin hasn't worked since I bought the boat. Finally pulled it down last night and exposed the wires leading to it. My multimeter is reading 1.5V. I was expecting something closer to 12 or 0, and so I wonder what could lead to 1.5. Is 1.5V the kind of...

Anybody have numbers for these parts? the dome and spreader lights?

...less than 50% of its capacity, or 12.2V. But if 12.2V is 50%, then 0% must be about 11.8. So again, I wonder what the difference is between 'exhausted', 'dead', 'discharged', and '0% capacity'. And if I leave my dome light on for a week, should I expect my battery to drain to 11.8V or to...

I am going to replace my Taco lights next year. The Grady Lumitec dome light with touch lens tech is awesome. My switches on the OEM dome light failed several times. The Lumitech light is sealed. It is really well built. It is a fantastic upgrade.

I cannot recall but I think the answer is no. Even if you do, no big deal. I used 4200 to seal.

Did you have to drill new holes for yours? Looks like the ones that are on there are front and back screws the led are side screw mounted.

The LED attwood lights are direct replacements. You can probably change the bulb in the mast light. I did that but my mast light came with the radar dome. https://www.starmarinedepot.com/attwood ... gJC5vD_BwE

It's from my Grady dealer. It's made by Lumitec. I've seen Lumitec domes in WM, but not sure if they are setup to control the spreaders also. It's pricey, but a very nice upgrade from the old one with the push buttons that die. It's SmokyMtnGrady's fault I bought it, just trying to keep up. 8)

KY Grady, do you have a link or the info on your replacement LED dome light?

The ones that replaced the original halogens are still controlled by the "spreader" switch on the helm dome light. I just bought a 3 position pull switch (off/1 on/both on) to control the new ones under the anchor pulpit and the one facing fwd on the hardtop. The switch will be mounted in the...

Mine is on the helm dome light. Also swapped out the helm dome light for a LED one and the switches are now touch, no more push button.

When you guys swap out your spreader lights are you controlling them with the toggle switch on the helm dome light or running through a whole new switch?

Unfortunately those are not LED lights. I'd re-use my existing fluorescent light rather than buying those.

https://www.ebay.com/itm/GRADY-WHITE-DA ... Cy&vxp=mtr might do the trick...

Here is a couple of links for these. I recall folks looking for them. http://www.ebay.com/itm/GRADY-WHITE-OEM ... hA&vxp=mtr http://www.ebay.com/itm/GRADY-WHITE-3-W ... ux&vxp=mtr I also found a complete set of GW helm switch covers out there as well. Perfect fit and they had a complete set...