Search results

Look in the bilge aft through the pie plates. Look for sea cocks with levers. At a minimum you would have one but more likely two. Depending on how the boat was rigged, you might have three if the boat has a toilet with overboard discharge plumbing. If so, the hose connected to that seacock for...

I got a pop up ad this morning. Should I have?

Got it.. Let us know what you find.

I read the manual and the transfer function is built-in to the inverter and is automatic, So no manual transfer switch. The AC Input light on the control panel should be lit when shore power connected and off when there is no shore power. In order for the unit to invert, the inverter switch...

Welcome to the forum and best wishes for your SKOKUM

The Seakeeper Ride kicks in at 10 MPH so it does nothing when rolling but not moving forward faster than 10 MPH. There are other advantages to the system though. In addition to lessening rolling, it can also adjust trim when networked with the motor network. That can help keep the bow up or down...

Are you referring to the Trim caps that cover the screw heads? If so, look at PRO-DEC.com for the biggest selection

I had a similar issue with a previous boat. In that instance I had to enlarge the holes in the fiberglass side panels. That was a pain in the neck, dusty job. I used down cut jig saw blades to reduce chipping. That did reduce chipping but the fiberglass ate up the blades quickly

I think there should be a breaker somewhere that selects the AC voltage source to be from either the gen set or the inverter. Just a guess. Secondly, I would expect the unit to be relatively close to the battery bank to limit cable lengths for the charging function

Actually it doesn't look all that bad for a 24 year old hull. There are stress cracks, mostly where one would expect to see them with the possible exception of the crack at the top of the stringer on the right side of the first picture. I would do a tapping test all over the transom to listen...

The answer is the same: It all depends on the bank or whatever loan agent is used. Why do you care whether the buyer can get a loan? If he or she can't, find another buyer.

Whether a lender will issue a loan to a buyer on a boat doesn't have anything to do with a current load owed by the seller. The buyers credit history and finances will be a much bigger factor than the boat's age.

And I though it was me:)

Good info. It took me a while to find the actual link to wherever this info was posted on the Grady site but eventually I found it Go to the link and then click the page control to page 5. https://www.gradywhite.com/explore/grady-owners/customer-tips/?category=4692&skip=36&year=&keyword= I...

I don't understand how the t-stats would make the engine vibrate and have no power. Did that happen when first started or did you have to run it a while and then it started to act up? If it overheated and then you got alarms and vibrations, I guess I can understand that case. You also got...

The tank either leaks or it doesn't:) No smell is a good sign but even if it doesn't leak, there is no easy way to determine how much life it may have. I would a bit concerned about possible exhaust stack corrosion. Make sure you get the exhaust inspected.

I am not sure exactly what Yamaha says about fogging but on some motors, it is not recommended to fog through the intake since the oil can damage the mass air flow sensor. If the plug that went bad was the same on both engines, I have to wonder if it was something you did that fouled the plugs...

What was your motor model? What method did you use to fog the motor? Was it the same cylinder in both motors that was mis firing?

Be careful mixing chemicals like chlorine bleach with other cleansers. It's best not to mix any cleanser with another. 4200 and 5200 for that mater are adhesives that also seal but are not sealants. The adhesives are intended for parts that don't move with respect to the other parts they are...

You didn't mention how old the caulk is ( original to the hull year) but the caulks generally have a mildewcide that over time looses their potency. You may not be able to remove all of the stain. Try the bleach as mentioned but apply it to the caulk and do not let it sit on the gel coats for...