Search results

Great job! I'm in the midst of an electronics upgrade and remote steering for the kicker and a removable cobia tower is my next major upgrade.

I chose inreach because I heard the satellite network spot uses is "spotty". I don't really know but may want to look into that.

I'm reading about this now, probably my next gadget. Thanks.

It depends on your chart plotter head unit. Each (major) manufacture makes their own and there are generic modules that connect via NEMA2000. Then you need a subscription through XM and there are several options that offer different services. Not cheap but hey, it's a boat...

I don't wear a lifejacket unless I'm running in the dark or its really rough but otherwise my gear list, philosophy, and approach is similar to everwhom. I almost sunk few years ago about 60 miles out on a friend's boat and it taught me a few important lessons. I a do wear the Inreach Mini and...

No, I just used 4 of the big washers used for mounting engines.

Garmin Inreach.

Does this problem occur when you're running or trolling? Many alternators barely produce enough Amps to run the engine when operating at idle speed. Running a GPS and misc accessories while trolling and you're probably running at a deficit when trolling.

Thanks for the report and good way to end it on some Sea Bass. I'm keeping my boat in OCMD this season but I'll be running my brother's new 28' Regulator out of the Atlantic Highlands this summer. I'll let you know next time we make a run at it and let's hope it turns on again like last year.

A better photo and next I'll be posting about gelcoat repair... I was solo again and it was a struggle to get it over the rail all lit up.

I ran out of Oregon Inlet today, 10 minutes down the beach the Talica 16 with a Stretch 25 chirped a little drag and quickly netted a 34" Cobia, not a bad start. 10 minutes later the same rod goes off but this time it was a screamer. I'm thinking I must have snagged a ray or a shark but...

I'm in OBX on Vaca so ran solo about 25 miles out of Hateras yesterday. To say that inlet is tricky would be a major understatement but followed other boats and made my way. Boated a couple Dolphin and missed a few, and shagged a hundred lbs of weed out on the 100f line. On my way in I...

I also bought the 16" x 24" DPI hatch and just getting ready to break out the saw... unfortunately I pulled my deck panel and my lateral supports are much closer together than PNY's. I could probably squeeze it in between using a router but it would then the water tank would start to interfere...

Not perko but I added a second FW outlet under the SW on my Seafarer. I still plan to use the Cockpit shower most of the time and move the hose from the SW to the FW when I want to do a bigger FW washdown. My first trip out I discovered I messed up the SW connection so just kept the hose...

I put a pull start manual tilt F6 on my Whaler about 20 years ago so I have some experience with manual and last spring I put a F9.9 with electric start and electric trim on my 228, it's like night and day, love it. Plus, all the bouncing around eventually destroyed the bracket assembly that...

I was down in KCB a few weeks ago. If you're not familiar the west entrance where I marked is a good bait spot. Put out a block of chum and you can get pinfish on bait and pilchards on sabinki day or night. The other spot I marked is the channel on the south side just east of vaca cut is...

I bought a set of the large washers and bolts used to mount engines and that transom is much thicker than expected. 2.5" if i recall. One word of advice is don't drill into the transom dead on horizontally. If you do the washers won't and the bolts won't sit right because the transom...

That's what I would recommend. The Jacobsen bracket is made of 1/2" aluminum so very solid construction and the way its mounted I could probably lift the entire boat from it if I attached it to a crane, seriously. Also the powder coat is the same color as my hull, the Adventure bracket is...

It's been a year but as I recall if I positioned the bottom of the Adventure bracket on top of that piston then the upper bolts would come through that horizontal cross beam making it wonky to through bolt and I didn't want to use lag bolts on the upper. When I spoke with Adventure Marine...

I returned it so I really can't say. My issue is I didn't want to cut it to fit around that trim tab piston since it's powder coated (on the exterior) and it's hollow so it'll fill with water and corrode. The other issue with the Adventure Marine bracket is its much longer so the kicker will...