Search results

Here's how I did it: Remove the black switch panel at the helm (near the throttles). Remove the entire starboard side panel in the aft bunk covering up the head unit. Not just the small panel. Carefully remove the AC/DC Panel in the cabin and let it hang. Run a snake from the starboard cabin...

I also repowered from 2006 3.3L F250's to 2022 4.2L F300's with digital controls. I'm using my same 17 pitch 4 Blade props and I'm seeing cruise at 28 knots Vs. 24 knots with the exact same economy. Also seeing a little bit higher end at WOT but not much frankly (3 knots more I'd say). The...

Major Woods, Is this Kit (see 3 items frequently bought together) what you installed...

I've done it. A good air mattress, sleeping bag and a wool cap is all you need. Sleep under the stars... Having a tarp handy is a good idea if there is fog, light rain or a morning dew.

I agree it is likely starving from fuel but it could be the relay. You can try swapping the starter relay with the fuel relay (they are the same). After the swap, if the starter turns the engine, you know it's good. If not, you know it's bad. For fuel, you must be sure the filters are clean...

As promised, here is my update... Today, I received and installed a new Solenoid/fuel valve assembly purchased from Fischer Panda in Florida. The generator started right up and ran flawlessly for one and a half hours before I shut it down (after cooling the vanes with no load for 10 minutes)...

Good question Bill. They were good or at least not out of whack. I reset them at .2mm. Once I receive and install the new solenoid + valve, I will report back.

I agree with Kirk (above). Years ago, I think I replaced the motor when the issue was the wiring to the switch.

Thanks for that. My wire connections + fuses and relays are all good. Any use of Starting Fluid is a band aid and should not be viewed as a long term fix. I still have an issue... I am in the process of replacing the fuel soleniod & valve. On order now and I receive it tomorrow. The one in...

Update: I was able to get my Fischer Panda started again. I consulted with a graybeard Diesel Mechanic and he suggested I spray some Starter Fluid into the Air Intake. I did this and my generator fired right up. Evidently, the Mechanic said I had air somewhere in the fuel line. Once I got it...

Good input Bill. I will check the Valves again. I did it a long time ago (maybe 200 hours?) and I forget how, I did it. Any tips for me? Thanks, Jack

2006 Fischer Panda 4200 installed in my 330 Express. 985 hours. My generator has been otherwise reliable but recently I can't get it to start. The starter turns the engine over and over but no start. About a month ago, I had gunk in my tank which plugged up the pump's pre-filter & fuel pump...

I always recommend for all to install a High Water Alarm in your bilge. My 330 has 2 (aft and forward). Your lights on your bilge pumps are very nice but there is nothing that gets your attention more than a loud audible which a high water alarm delivers. Getting advance notice of a problem...

Yes. Use good quality SS Bolts with SS fender washers underneath if possible to bear the load of the rod.

One word answer for me too: YES.

I would closely inspect your 6" "push in" inspection ports (aka deck plates). The gaskets, if not replaced, are 24 years old and probably leak alot. I replaced most of my push in plates with the screw in kind which seal much much better. I used 6" Beckson brand deck plates in almond color...

Here's what I did on my 330 and it works great. 1. On port and starboard sides of your vee berth, unscrew those 6' long teak strips (you can always re-install later). 2. On the areas there that protrude a bit mount these >>> https://tacomarine.com/sport-fishing-rod-holders-f16-2752 3...

That cockpit rocket launcher/table in Sardinia is the wrong color (pure white) and it's installed backwards. The Drawers should face forward, not aft, in my opinion. Other than that, it looks like a nice unit. I think one needs to spend time on the water to see if you like such a thing. I...

What you have there is an excellent choice and solution. The 38" width might? be a tad wide, not sure. When I bought my 2006 330 13 years ago, it had a rectangular (18' X 30") Birdsall Marine table with 4 rod holders and 2 cup holders. Like this one >>>...

I repowered my 2006 330 with DES F300's built in 2021. Using PowerTech OFS 4 blades in 16 pitch. WOT reaches 5,800 RPM's. I cruise comfortably at 28 knots 4,300-4,400 RPM's all day long. I tried a set of PowerTech OFS 4 blades in 15 pitch and didn't like them. The 15 pitch had me at...