Dome light upgrade

[Hookup1]

My plastic 1997 vintage dome light at the helm needs to be replaced. Lens cracked and the housing UV damaged.

I can't find the OEM dome. I have read here that GW has switched to a Lumitec red/white touch with spreader light. Has anyone made the switch and where did you get it.

 

[TeK]

Just a thought…find one that’s similar and add another switch.

 

[Hookup1]

I call the GW dealer yesterday. Parts guy told me he has had half dozen inquires for the Lumitec with the spreader light switch - no longer available. I ordered one to see if it can be adapted but probably not. Have to put the spreader lights on the panel next to the livewell.

I hate projects like this. All I want to do is put the same thing back - for better or worse - and not have to find something else, drill new mounting holes and re-wire things.

 

[Halfhitch]

How about one of these?

https://www.greatlakesskipper.com/perko-boat-dome-light-1253dp1wht-tracker-marine-12v-ivory-4-inch

https://www.greatlakesskipper.com/perko-boat-dome-light-300-002chr-surface-mount-6-inch-silver-12v

If you are talking about the one like was on the older Gradys with the extra switch for the spreader lights, you could check with a Proline Boat dealer. They use them and I heard they can still get them? I never called them myself.

 

[SkunkBoat]

Spreaders are fed from the E-box. Easier to put a switch up there. Think about adding another light or two on the top and then use a 3 or 4 position push-pull switch in the E-box.

 

[Fishtales]

How about using an accessory switch on the helm panel?

 

[Finatic272]

I had the same problem with my light an my 1999Sailfish. I purchased a dome light with the red/ white light. Removed the spr

 

[Finatic272]

Sorry my message got submitted before I was done…. I purchased a dome light with the red/ white switch. Removed the spreader switch from my old dome light. Drilled a hold in the new dome light installed the spreader switch. Works great.

 

[Halfhitch]

I had the same problem with my light an my 1999Sailfish. I purchased a dome light with the red/ white light. Removed the spr

When you accidently post your message before you are finished with it, you can just click on "Edit" at the bottom of your abbreviated message and complete it without having to retype everything.

 

[A&J Outdoors]

Sorry my message got submitted before I was done…. I purchased a dome light with the red/ white switch. Removed the spreader switch from my old dome light. Drilled a hold in the new dome light installed the spreader switch. Works great.

Sounds like a good solution, I am facing the same issue with my dome light, it looks like crap and works when it feels like it.

 

[Hookup1]

I’ll look at this again this weekend. I like the Lumitec but it may be completely sealed and no place to install a spreader light switch.

 

[Hookup1]

Sent the unit back. Starting over.

 

[SkunkBoat]

Get one without spreader switch and then use this for spreaders. You can add forward or side spreaders and wire it 1, 2, both

 

[wrxhoon]

When mine stopped working I contacted Lumitec and they replaced it free of charge . I have 2013 228 and this was about two years ago. They normally want the old one back but due to cost from Australia they asked me to send photos with the rear cables cut close to the sealed part.
I was told that they make it specifically for GW. They make the same light without the spreader light switch .
The reason mine stopped working, water got in it .
Excellent service from Lumitec to replace a light that old free and they even paid for shipping to AU.

 

[Hookup1]

Original light was a Guest. Marino bought them but have since discontinued making dome light. I found a Marino Guest dome light single color no switch. They appear to use the exact same base with a different lens. I ordered one today. I'll move my red lamp and switches over. I'll post results.

I looked at the Lumitec but didn't like the single LED in a 6" diameter dome light. Touch controls were clumsy. On its way back to Amazon.

 

[Bilpep]

Check out wave one marine in Florida. That gave done this before. Just need to add/use your old switch

 

[Hookup1]

The Marinco/Guest new old stock dome light I found online came in. Same mold. Quick rework to install switches and red lamp. Done!

 

[Hookup1]

A little cyanoacrylate on the rubber trim and hot glue on the wires. Keep everything in place when putting back up. Otherwise they are a pain with everything moving around.

 

[5-Salt]

These work

 

[Hookup1]

Wasn’t a switch problem. The lens and housing looked like crap. I’m working on getting another housing for a spare. I have plenty of switches from DigiKey in my spares. They also have the combo switch for red/white light selection.