Recent 228 and pressure washer OK?

luckydude

GreatGrady Captain
Joined
Jun 5, 2020
Messages
1,288
Reaction score
601
Points
113
Age
62
Location
Santa Cruz Mountains, CA
Website
mcvoy.com
Model
Seafarer
I've already got some stubborn stains that I'm pretty sure a pressure washer will clean off. Up until now, I've used a nozzle on a hose and a brush and that is getting old.

Are there any issues with using a pressure washer on a 228? I'm Mr Idiot, but not so much that I'd use the solid stream, that will take paint off. I'm thinking the 25 degree fan of water, can I use that everywhere or are there some places that it would strip stuff off or damage something?
 

Pighunter

Well-Known Member
Joined
Feb 23, 2020
Messages
401
Reaction score
137
Points
43
Age
63
I've already got some stubborn stains that I'm pretty sure a pressure washer will clean off. Up until now, I've used a nozzle on a hose and a brush and that is getting old.

Are there any issues with using a pressure washer on a 228? I'm Mr Idiot, but not so much that I'd use the solid stream, that will take paint off. I'm thinking the 25 degree fan of water, can I use that everywhere or are there some places that it would strip stuff off or damage something?

I used a pressure washer on mine, especially the deck had some stains it cleared them right off with no damage to the glass.
 

Sdfish

Well-Known Member
Joined
Sep 15, 2013
Messages
506
Reaction score
174
Points
43
Location
San Diego, California
Model
Adventure
It may just be me, but I have always been hesitant to use a power washer on the boat. Lots of folks do it successfully though.
 

Parthery

GreatGrady Captain
Joined
Jan 31, 2005
Messages
2,589
Reaction score
220
Points
63
Location
Atlanta, GA
You will be fine on the gelcoat. Just take your cushions off. You can destroy them in a hurry.

If you have bolsters be careful around them too.
 

Pighunter

Well-Known Member
Joined
Feb 23, 2020
Messages
401
Reaction score
137
Points
43
Age
63
interesting to know type of stain? have a picture?
Mine was stains from the previous owner (looked like blood that never got cleaned??)so I'm not sure but I tried a good industrial fiberglass cleaner with a heavy brush and it wouldn't touch them. So I put the power washer right on them and they were gone.
 

Flot

Well-Known Member
Joined
Dec 1, 2018
Messages
165
Reaction score
40
Points
28
Age
48
Model
Express 330
You'll be fine with a 25 deg tip on a pressure washer.

Personally I'm a big fan of bleach on boats. It is amazing what a bleach + dish soap solution will clean. That said, any sort of caustic cleaner will "damage" the fiberglass over time and most dedicated boat soap / deck cleaner products are pretty good. But I've doused 20 years of boats with bleach and haven't regretted it yet. (but similar to the above cautions, bleach is mostly safe for vinyl but very bad for the stitching on your cushions)

Of course, YMMV.
 

seasick

Well-Known Member
Joined
Aug 19, 2008
Messages
9,529
Reaction score
1,420
Points
113
Location
NYC
Barkeepers Friend with OXY works quite well.
The question about the pressure washer is not straight forward. The rated pressure of the power washer, especially a gas unit, and the nozzle used are important. A washer rated neat 3000 psi with the narrow nozzle can actually remove gel coat and fiberglass as well as the skin on your hands or feet. ( There is rarely if ever a reason to use the red nozzle!)
For me, I prefer to use an appropriate cleanser/solvent for specific stains. For example, tree sap may require a petroleum based cleaner whereas hull staining near the water line would need an oxalic acid type of cleaner.
My standard inventory has On and Off hull cleaner, Acetone, boat soap, a barnacle remover ( here is where a spatula and a power washer really help), a mold cleaner and a black streak remover.
I also use a very mild polishing compound (Presta Finesses I think its called) to remove hull streaks and smudges caused by rubbing fenders and dock edges.
 

Bloodweiser

Well-Known Member
Joined
Feb 10, 2020
Messages
650
Reaction score
169
Points
43
Age
51
Location
Northern Cal
Model
Seafarer
X2 on barkeepers friend that’s good stuff.and available at Home Depot
 

Blaugrana

Well-Known Member
Joined
Sep 16, 2019
Messages
703
Reaction score
107
Points
43
Age
41
Location
Bayville, New Jersey
Model
Seafarer
Not sure what surface, but I use starbrite non skid deck cleaner on all stains that soap by itself won’t take out.

I have been impressed with how nice it works with no real efforr
 
  • Like
Reactions: Bloodweiser

seasick

Well-Known Member
Joined
Aug 19, 2008
Messages
9,529
Reaction score
1,420
Points
113
Location
NYC
Here are some products that I use.
Woody Wax for decks and metals. Expensive but worth it. Flitz is also very good for metal.

303 Protectant. Good for vinyl and clear vinyl. I use it every fall before the storage of my cushions.
Starbrite water repellent. I used to use 303 Fabric but it is expensive if you want to treat large areas like Biminis, helm covers and the like, the Starbrite is a better deal. If I had new canvas, I probably would go back to 303 for several seasons.
Gary's wax. I have been using this for a decade or more. Maybe there are better waxes but it works for me so I stick with it.
Presta Finesse cream. A very light polish/compound. Good for rub marks.

Water line stains. Mary Kate On&Off. If I have options, I will but the less expensive options as long as they have oxalic acid in them. Note that hull cleaners are not friendly to galvanized trailers.

Black streaks. I haven't found a products that works really well for me. I usually end up just using a cleaner wax for light streaks or a mild polish for tougher ones.

Barnacles. After power washing and some scraping, the remaining pieces can be tough to remove. Muritic acid works very well but is also a dangerous material and probably banned at many marinas. The fumes can do serious damage. I probably shouldn't even have mentioned it. After reading up on barnacles, I am going to try a lime remover like CLR to see if it works.

Barkeepers Friend, the milder stuff ( says it's good for non stick pans)
With respect to diamond non skid decks, I have stated in the past and still believe that for some unknown reason, scrubbing with a cleanser and a rag works much better than the cleanser and a brush, soft or stiff. The trick with the rag is to scrub in one direction of the grooves and then scrub along the other direction of the grooves. For abrasive types of non skid, forget the rag, just brush.
I welcome others feedback
 

luckydude

GreatGrady Captain
Joined
Jun 5, 2020
Messages
1,288
Reaction score
601
Points
113
Age
62
Location
Santa Cruz Mountains, CA
Website
mcvoy.com
Model
Seafarer
Huh, pressure washer did not take most of the stains off. I'm fishing tomorrow but I'll get pics after I wash the decks when we get home. I think it might be tree sap or something like that.
 

Sparkdog118

Well-Known Member
Joined
Apr 8, 2020
Messages
629
Reaction score
134
Points
43
Age
54
Location
Ft Myers, fl
Model
Offshore
Here are some products that I use.
Woody Wax for decks and metals. Expensive but worth it. Flitz is also very good for metal.

303 Protectant. Good for vinyl and clear vinyl. I use it every fall before the storage of my cushions.
Starbrite water repellent. I used to use 303 Fabric but it is expensive if you want to treat large areas like Biminis, helm covers and the like, the Starbrite is a better deal. If I had new canvas, I probably would go back to 303 for several seasons.
Gary's wax. I have been using this for a decade or more. Maybe there are better waxes but it works for me so I stick with it.
Presta Finesse cream. A very light polish/compound. Good for rub marks.

Water line stains. Mary Kate On&Off. If I have options, I will but the less expensive options as long as they have oxalic acid in them. Note that hull cleaners are not friendly to galvanized trailers.

Black streaks. I haven't found a products that works really well for me. I usually end up just using a cleaner wax for light streaks or a mild polish for tougher ones.

Barnacles. After power washing and some scraping, the remaining pieces can be tough to remove. Muritic acid works very well but is also a dangerous material and probably banned at many marinas. The fumes can do serious damage. I probably shouldn't even have mentioned it. After reading up on barnacles, I am going to try a lime remover like CLR to see if it works.

Barkeepers Friend, the milder stuff ( says it's good for non stick pans)
With respect to diamond non skid decks, I have stated in the past and still believe that for some unknown reason, scrubbing with a cleanser and a rag works much better than the cleanser and a brush, soft or stiff. The trick with the rag is to scrub in one direction of the grooves and then scrub along the other direction of the grooves. For abrasive types of non skid, forget the rag, just brush.
I welcome others feedback
The product that I have found works well for the waterline stains Is rust aid from Home Depot. It is much cheaper than on off and works just as well.
For the black streaks, I use oil eater (usually a 50/50 mix with water. It cleans the black steaks and the oily finger marks up great off your fiberglass after working on the engine. Also works well for degreasing your engine and cleaning your tires.
 

Attachments

  • CFDBC1B6-1BF3-46D4-A379-14C15F196395.jpeg
    CFDBC1B6-1BF3-46D4-A379-14C15F196395.jpeg
    264.5 KB · Views: 1
  • 454508F4-539E-4AC2-AF82-52CB421A0312.jpeg
    454508F4-539E-4AC2-AF82-52CB421A0312.jpeg
    262.6 KB · Views: 1

seasick

Well-Known Member
Joined
Aug 19, 2008
Messages
9,529
Reaction score
1,420
Points
113
Location
NYC
I am going to try the rust aid. I looked up the data sheet and it's active ingredient is oxalic acid with a dash of hydroflouric acid
 

nuclear

Well-Known Member
Joined
Jun 15, 2020
Messages
219
Reaction score
81
Points
28
Model
Seafarer
For waterline stains, the cheapest oxalic acid you can get is "The Works" toilet bowl cleaner at the dollar store. Just make sure you continually are rinsing everything with the hose while you use it, especially the trailer.