Seacock stuck

Harrysea

Well-Known Member
Joined
Apr 24, 2021
Messages
123
Reaction score
41
Points
28
Location
Apollo Beach, FL
Model
Marlin
I’m the new owner of a 2006 Marlin 300. Love the boat! But the livewell seacock and the A/C seacock are both stuck open. I don‘t want to force them, but I do want to be able to close them. Any advice?
 

grady33

GreatGrady Captain
Joined
Jun 30, 2008
Messages
727
Reaction score
80
Points
28
Location
Ocean Pines, MD
Model
Express 330
Following. I have a 330 and the bronze thru Hull for pump out is really hard to turn. I was wondering if taking the hose off and spraying some sort of lubricant in there would work?
 
  • Like
Reactions: PointedRose

blindmullet

Well-Known Member
Joined
Oct 19, 2015
Messages
449
Reaction score
106
Points
43
Location
Florida
Model
Explorer
Try using some PB Blaster on it to loosen it up. If you get it freed up work the handle and lube at the same time.
 
  • Like
Reactions: SmokyMtnGrady

PointedRose

Well-Known Member
Joined
Feb 11, 2021
Messages
679
Reaction score
212
Points
43
Location
San Francisco
Model
Overnighter
Following. I have a 330 and the bronze thru Hull for pump out is really hard to turn. I was wondering if taking the hose off and spraying some sort of lubricant in there would work?
I’d try CLR
 

glacierbaze

Well-Known Member
Joined
Jul 6, 2012
Messages
2,488
Reaction score
644
Points
113
Age
75
Location
Chapel Hill and Pine Knoll Shores, NC
Model
Seafarer
Most of the old ones have a small drain plug, which can be replaced with a grease zerk. Some of the newer ones(Groco) have a drain and a zerk. Grease them in the open position, or the grease goes into the center of the ball valve, instead of against the side.

 
  • Like
Reactions: PointedRose

DennisG01

GreatGrady Captain
Joined
Sep 1, 2013
Messages
7,190
Reaction score
1,341
Points
113
Location
Allentown, PA & Friendship, ME
Model
Offshore
After freeing it up (PB Blaster, silicone spray, etc - and/or adding the zerk), be sure to exercise the seacock once a month to keep it in good shape. Use to some leverage to get it to start moving - some handles have a square that a socket wrench can be inserted - you can also slip a pipe over the handle for extra leverage. A little bit back and forth, back and forth should do it.
 
  • Like
Reactions: SmokyMtnGrady

Finest Kind

Well-Known Member
Joined
Jul 11, 2005
Messages
461
Reaction score
71
Points
28
Location
Hallandale, Fl
Or, if none of the suggestions above work and you cant free it, just leave it open and install a new shut off valve on the hose itself.
 

ElyseM

GreatGrady Captain
Joined
Nov 18, 2007
Messages
949
Reaction score
54
Points
28
Location
highlands, nj
if they don't move easily once you work on them, time for new ones. they should be screwed in to the thru hull pickup so it should be straight forward replacement. need i say ALL work would be best done on the hard?

good luck, ron
 
  • Like
Reactions: PointedRose

Blaugrana

Well-Known Member
Joined
Sep 16, 2019
Messages
703
Reaction score
107
Points
43
Age
41
Location
Bayville, New Jersey
Model
Seafarer
Make sure you are pulling the seacock at the appropriate angle. When I first got my boat, I thought neither worked but it was because I was pulling up rather than the angle at which the rod was expecting. You may need to pull or push depending on it’s position
 

Hookup1

GreatGrady Captain
Joined
Oct 16, 2007
Messages
3,035
Reaction score
855
Points
113
Age
70
Location
Cape May, NJ
Model
Islander
If they are left open in salt water for most of their life the marine growth gets up inside and "locks" them in place. Frequently you see this on the large inboards where they won't close all the way. But it does happen to the smaller ones. I can't honestly say what would happen if I tried to close mine!
 

everwhom

GreatGrady Captain
Joined
Sep 1, 2015
Messages
445
Reaction score
80
Points
28
Location
Cape Cod and Nantucket
I think a fair few folks leave them open all the time -- no criticism intended, but I'm not sure they realize how many boats sink at the slip because of a failed hose clamp or leaky hose. With the seacock open the only thing keeping your boat floating is a hose and some clamps in your bilge that may be as old as the boat! I usually open the ones I need at the beginning of a trip and close them all at the end: I always think (1) battery switches are off, (2) shore power & battery charger on, and (3) seacocks closed

The only one I rarely / never use is the head discharge so sometimes I will go several months before I remember to try it. It always turns easily though, so I suspect that the seacocks that are closed don't get stuck as easily due to marine life.
 

Legend

GreatGrady Captain
Joined
Jun 29, 2006
Messages
1,462
Reaction score
201
Points
63
Location
Southern New England
Model
Sailfish

This is a handy leverage tool for hard to reach and tough to move seacock. I would be cautious of using it if you seacock is frozen as it could end break it. Use it if your seacock is not getting enough use bc it is 3 feet below deck as many GW are designed
 

SmokyMtnGrady

Well-Known Member
Joined
Jul 11, 2009
Messages
2,020
Reaction score
504
Points
113
I think a fair few folks leave them open all the time -- no criticism intended, but I'm not sure they realize how many boats sink at the slip because of a failed hose clamp or leaky hose. With the seacock open the only thing keeping your boat floating is a hose and some clamps in your bilge that may be as old as the boat! I usually open the ones I need at the beginning of a trip and close them all at the end: I always think (1) battery switches are off, (2) shore power & battery charger on, and (3) seacocks closed

The only one I rarely / never use is the head discharge so sometimes I will go several months before I remember to try it. It always turns easily though, so I suspect that the seacocks that are closed don't get stuck as easily due to marine life.
Exactly. I would go as far if you're not using it while underway ,don't open it. There is a lot of water pressure say on your washdown pump if you leave the raw water open all the time. mine are closed all the time unless I need it. in the winter they are opened , well they are opened before the first freeze in October for us. Like other said use a penetrating lubricant like PB to help loosen it up. Good luck.

Question: Mine get exercised regularly. Thus thread got me wondering. When my boat is on the trailer can I just shoot some lubricant like triflo up into them through the bottom opening? I know this sounds dumb but. I never though of lubricating from the inside before. Thanks .
 

DennisG01

GreatGrady Captain
Joined
Sep 1, 2013
Messages
7,190
Reaction score
1,341
Points
113
Location
Allentown, PA & Friendship, ME
Model
Offshore
I think I mentioned it above, but be sure to check the handle for a square hole at the end for a socket. If the handle is fully encased, the hole still might be there underneath.
Question: Mine get exercised regularly. Thus thread got me wondering. When my boat is on the trailer can I just shoot some lubricant like triflo up into them through the bottom opening? I know this sounds dumb but. I never though of lubricating from the inside before. Thanks .
I don't see how it can hurt. I'm not sure how effective it would be, either, since the valve is the open position and the idea would be to get some stuff between the valve and the valve body. But some stuff might creep in. But then go inside and exercise the handle a few times right away.
 

Harrysea

Well-Known Member
Joined
Apr 24, 2021
Messages
123
Reaction score
41
Points
28
Location
Apollo Beach, FL
Model
Marlin
Thanks for all the advice. Finally got my last seacock closed today. I’ve been using PB Blaster periodically for the last couple of weeks. Today I pulled the deck plate and went after the last stuck seacock with gentle taps until it finally let go. All the hoses and clamps look to be in good shape, but I’ll feel better running with seacocks closed until they need to be opened.
 

family affair

Well-Known Member
Joined
Jul 31, 2010
Messages
1,437
Reaction score
339
Points
83
Location
Ohio
Model
Islander
My $0.02 - make sure whatever lube you are using is rubber friendly.
 
  • Like
Reactions: Zebulon

Fishtales

Well-Known Member
Joined
Jan 31, 2005
Messages
8,033
Reaction score
1,286
Points
113
A good penetrating oil every year on them as well as the slides (if you have that allow access thru the deck plate.