Trolling motor install on 282 Sailfish

[Wild blue]

I test drove a 272 in Cape Coral that had Rhodan 84” on it with 3 lithium batteries, the issue here was charging the lithium batteries takes a higher output than what the engines could produce so all charging came from shore power, about 3hrs of spot lock in marginal wind and current before the boat started to drift and couldn’t keep up according to the seller, I’ll find a pic

 

[SecondWind282]

I have finished a wood template for my 96” Rhodan for my 282. I did not want to cut the bow rail so I made a plate that attaches to the pulpit. I have some preliminary pictures though I have extended the final template back to the windless. I attached a rope to the bottom of the shaft to assist with deployment and recovery. The final is at the fabricators shop and I’m just waiting for it to be complete so I can get it coated. The ropes in the picture are just for safety since I wasn’t sure if the wood would crack or not. I’ll post pics of the final once it’s done.

I like this concept a lot, thanks for sharing. I like how this doesn't require mods to bow rail or the nav lights.

Taking this a little further, this mounting plate could be easily removable if the top plate is made wider than the pulpit, say about 1" projecting on the non-mount side (mount side is already projecting). There could be two 1/2" dia holes on each projecting side, just clear of the pulpit. A bottom plate could be made with matching hole pattern to act as a clamp plate when thru bolts with lock nuts are installed. The contact side of both plates could be lined with an adhered thin layer of high density rubber backing to add grip and protect the gel coat when clamped. This could be easily removed if trolling motor won't be used or if trailering. Does not require any drilling into pulpit or boat.

What battery and charging setup are you going with?

 

[SouthFork]

I like this concept a lot, thanks for sharing. I like how this doesn't require mods to bow rail or the nav lights.

Taking this a little further, this mounting plate could be easily removable if the top plate is made wider than the pulpit, say about 1" projecting on the non-mount side (mount side is already projecting). There could be two 1/2" dia holes on each projecting side, just clear of the pulpit. A bottom plate could be made with matching hole pattern to act as a clamp plate when thru bolts with lock nuts are installed. The contact side of both plates could be lined with an adhered thin layer of high density rubber backing to add grip and protect the gel coat when clamped. This could be easily removed if trolling motor won't be used or if trailering. Does not require any drilling into pulpit or boat.

What battery and charging setup are you going with?

Good point, unfortunately it’s already being made and I did want it to be permanent. I’m going with 3 12v Interstate batteries in the compartment under the mid berth along with a genie 3 bank charger. My plan is going to be changing it up to lithium at some point but I got the batteries for cost from a friend. Because I’m planning on swapping batteries at some point I think I’m going to use an extension cord and plug it into one of the outlets since the boat is always hooked up to shore power.

 

[Finest Kind]

I was wondering why you decided on a 87" model, as opposed to a 96" (Rhodan)....
On that hull (similar to my Trophy Pro), will the 87" be long enough to still bite into the water when trying to hold in rough seas?

Now that I have some experience with the 96" Rhodan on my Trophy Pro (same hull as Sailfish), I can tell you NEED AT LEAST the 96". Unless you are only gonna fish bluebird flat days with no swell, the prop is definitely going to cavitate with an 87".

 

[Finest Kind]

I have finished a wood template for my 96” Rhodan for my 282. I did not want to cut the bow rail so I made a plate that attaches to the pulpit. I have some preliminary pictures though I have extended the final template back to the windless. I attached a rope to the bottom of the shaft to assist with deployment and recovery. The final is at the fabricators shop and I’m just waiting for it to be complete so I can get it coated. The ropes in the picture are just for safety since I wasn’t sure if the wood would crack or not. I’ll post pics of the final once it’s done.

I don't think that is a great idea.
You will be amazed at how much torque that Rhodan generates....that plus the wave action and currents pushing on the motor head leveraged by the long shaft is going to cause stress cracks and possibly result in the pulpit breaking apart.

 

[Accuratepete]

How are you going to screw it down. Will you be putting another plate on the bottom and are u cutting the rail

 

[SouthFork]

Well it took forever but I finally got the mount back from the fabricator. Now it’s off to get powder coated.

 

[SouthFork]

How are you going to screw it down. Will you be putting another plate on the bottom and are u cutting the rail

Yes I’m going to use 1/2” bolts with a backing plate.

 

[Andrewells134]

Has anyone attempted to install on of the new 87” shaft Minn Kota Riptide Terrova trolling motors on the bow of a 282 Sailfish?

Yes I recently had it done on my Sailfish, I had the bow mount strengthened, we adapted the bow rail to allow the trolling motor to raise up and lower. Now the stainless steel rail can open and close. The only thing I have left to do is to have a custom clip made to insert where the rail locks so rather than installing loosing the SS screw I can just insert a locking type pin that will be permanently attached to the rail so it won't fall into the Gulf of Mexico I an in the Houston area.

 

[SouthFork]

Tested my Rhodan today and it was flawless. Deploying it is easy than getting it back up but it is worth not cutting the rail. 282 Sailfish. Can’t wait till the wind dies down and I can hit the reef. I will say the 3/8 aluminum flexes at the higher thrust settings which is kind of concerning so I’ll be keeping an eye out. I’d say use 3/4” if your doing something similar.

 

[Ling king]

I just finished my install of 108” Rhodan on "Cream Puff" 282 Sailfish. 1/2" Aluminum plate, powder coated white on the bow pulpit. . Extended all rail bolts and anchor roller bolts. Powered with the EPOCH 36V 100Ah LiFeP04. Mounted in the front bow hatch, down below. On deck I installed a battery charger power port, at the passengers feet. In the (coffin bed, below) is the battery charger. Mounted the shut off switch right next to the anchor rope closet.

Taking 13 days off during the holidays and definitely will be at the islands trolling for halibut.

Shoot me any questions you may have.

 

[Ling king]

I just finished my install of 108” Rhodan on "Cream Puff" 282 Sailfish. 1/2" Aluminum plate, powder coated white on the bow pulpit. . Extended all rail bolts and anchor roller bolts. Powered with the EPOCH 36V 100Ah LiFeP04. Mounted in the front bow hatch, down below. On deck I installed a battery charger power port, at the passengers feet. In the (coffin bed, below) is the battery charger. Mounted the shut off switch right next to the anchor rope closet.

Taking 13 days off during the holidays and definitely will be at the islands trolling for halibut.

Shoot me any questions you may have.

I'll take some pics from the top. I didn't lose and deck space. Follows the rail.

 

[deepwaterdreamer111]

I was wondering why you decided on a 87" model, as opposed to a 96" (Rhodan)....
On that hull (similar to my Trophy Pro), will the 87" be long enough to still bite into the water when trying to hold in rough seas?

I installed the 87 in 36volt on my 1986 sailfish. It worked fine . Occasionally came out of the water in 3 to 4 ft swells.

 

[seasick]

I just finished my install of 108” Rhodan on "Cream Puff" 282 Sailfish. 1/2" Aluminum plate, powder coated white on the bow pulpit. . Extended all rail bolts and anchor roller bolts. Powered with the EPOCH 36V 100Ah LiFeP04. Mounted in the front bow hatch, down below. On deck I installed a battery charger power port, at the passengers feet. In the (coffin bed, below) is the battery charger. Mounted the shut off switch right next to the anchor rope closet.

Taking 13 days off during the holidays and definitely will be at the islands trolling for halibut.

Shoot me any questions you may have.

In the third photo of the 60A circuit breaker, can you explain the wiring. The colors are throwing me off At first glance, it looks like the breaker is inline with the black cable, which normally would be a the ground. The red whch I would expect to the positive feed looks like it goes through that hole in the back panel

 

[Placida Grady]

Has anyone attempted to install on of the new 87” shaft Minn Kota Riptide Terrova trolling motors on the bow of a 282 Sailfish?

This is how I did my 80 inch Rodan. Was able to mount the puck forward of and over a bit of the anchor slot on the pulpit so the anchor still works fine on the windlass below the motor and puck. Just have to hold the top of the motor below the bow rail as you put it down and pull it up before you let it get fully vertical. Works great in up to 2 foot seas, at least 3 times as much fishing time each trip out without having to anchor. Probably too late for you if you posted this in 2019, but I just joined the forum.

 

[amf282]

Hi all, I failed to answer a question some time ago. The battery life is awesome. We have never really had to push it to the limit but I actually got a couple of days on a single charge. The Rhodan is a strong trolling motor and holds our boat great. The rail cutout was a game changer in lowering and pulling back into riding position.

 

[Ling king]

In the third photo of the 60A circuit breaker, can you explain the wiring. The colors are throwing me off At first glance, it looks like the breaker is inline with the black cable, which normally would be a the ground. The red whch I would expect to the positive feed looks like it goes through that hole in the back panel

Re-wired, . Did not lose any deck space with the plate bolted to the pulpit.

 

[SouthFork]

Ling king how think is your aluminum? Mine is 3/8 and it flexes a lot at max power. I’m thinking I’ll need a second one and sandwich them together

 

[Ling king]

Will do. I haven’t taken her out yet. I have a buddy with the same setup on his Parker. The 1/2” plate is stronger than the pulpit.