Yamaha Speedometer inlet

dunwurkin

Well-Known Member
Joined
Jan 4, 2007
Messages
51
Reaction score
0
Points
0
Location
North Fork, LI
Exactly where are the inlets for the speedometer on the Yamaha 225's. My speedometer has been intermittent and then not working at all. I understand that the inlets may be clogged. Help

Thanks
 

Southern Hunter

Well-Known Member
Joined
Sep 24, 2007
Messages
177
Reaction score
0
Points
0
Location
Lafayette, Louisiana
On the bottom of the lower units on the front edge....there will be a small hole on each engine....which is where your boat registers its speed from.
 

fishingFINattic

Well-Known Member
Joined
Dec 21, 2006
Messages
412
Reaction score
4
Points
0
Location
S.E. Ct
I think it will only be on one motor - mine is on the starboard side only.
As mentioned above - a very small hole in the lower unit!
Tim
 

MDRookie01

Active Member
Joined
Mar 8, 2009
Messages
34
Reaction score
0
Points
0
speaking of yamaha 225 speedometers what does the clear tube read off the engine that is hooked to my speedometer? 1999 225
 

lgusto

Well-Known Member
Joined
Jan 19, 2008
Messages
281
Reaction score
4
Points
18
Location
Midcoast Maine and Florida Gulf Coast
The hole is amazingly smaller than one would think - like the size of a thin guitar string. On my 250 it got clogged so frequently I gave up on it. I hate not having everything on my boat in perfect working condition but I had to get over that item. The GPS speed over ground is far more accurate anyway.
 

magicalbill

GreatGrady Captain
Joined
Aug 15, 2005
Messages
1,663
Reaction score
314
Points
83
Location
Indiana
Model
Marlin
Like Igusto, my tube clogs up on my 200 four-stroke. Mostly in the Keys where I have to run thru enlongated narrow beds of seaweed floating on the surface.
I have been able to clear it out and make the speedo read correctly again by a hard reverse and then a blast of forward. Unfortunately this does not always work, and when it won't unclog, I take it to my selling/service dealer and they take the engine cover off and blow air gently thru the tubing...Out comes the offending particle(s) and the speedo reads perfectly.

Till the next time......
 

lgusto

Well-Known Member
Joined
Jan 19, 2008
Messages
281
Reaction score
4
Points
18
Location
Midcoast Maine and Florida Gulf Coast
To my knowledge, the "paper clip" solution is technically right. But for me, that hole was so small and the debris wedged in so hard that it didn't work. I've heard of guys drilling out the debris but I've also read of drill bits being broken off. It seems like compressed air back down the tube is the best approach, and the one I took. I just got tired of doing it every other week.
 

magicalbill

GreatGrady Captain
Joined
Aug 15, 2005
Messages
1,663
Reaction score
314
Points
83
Location
Indiana
Model
Marlin
I don't blame you..

I, too have the Garmin for accurate speed readings, but if the Yamaha speedo isn't functioning then my fuel MPG reading is affected. my trip odometer, and so on. I rely on those readings for trip/distance calculations.
Mine goes out a couple times a year..once in the Keys, and I usually ingest some random floating piece of crap in Lake Michigan.
Igusto, where do you boat that it screws up once a week?
 

NOTHING ELSE MATTERS

GreatGrady Captain
Joined
Jun 26, 2006
Messages
1,993
Reaction score
5
Points
38
Age
60
Location
LONG ISLAND NEW YORK
magicalbill said:
Seriously??

Worked for me three times so far, so yes, seriously.
If you use the drill you might punch a hole in the tubing and then you have bigger problems. I found out by washing the area every time i wash the boat with heavy soap helped a lot. On the engines i have now, i don't have that problem, there is no hole for speedo.
 

magicalbill

GreatGrady Captain
Joined
Aug 15, 2005
Messages
1,663
Reaction score
314
Points
83
Location
Indiana
Model
Marlin
Igusto..
Checked my PM Box..Nothing from you in there..

Maybe I hit a wrong button..

I'll check again in a bit...
 

Tuna Man

GreatGrady Captain
Joined
Mar 11, 2005
Messages
536
Reaction score
7
Points
18
Location
Rahway/Waretown NJ
I have used the drill trick bit a few times over the years also. I only used my hand to spin the drill bit, not a drill with a chuck. Never had a problem, just use a very small drill and be gentle (I think the bit was about 1/16"). With a sharp bit the wood fibers will come right out.
 

magicalbill

GreatGrady Captain
Joined
Aug 15, 2005
Messages
1,663
Reaction score
314
Points
83
Location
Indiana
Model
Marlin
Igusto..
Got your PM and sent you a reply back..Thanks..

Nothing Else Matters..

Thanks for the "paper clip insight." That is something I will definitely try in the shallows next time my tube clogs up..
 

dunwurkin

Well-Known Member
Joined
Jan 4, 2007
Messages
51
Reaction score
0
Points
0
Location
North Fork, LI
Hi All, Thanks for the input on the paper clip. I went to the boat today and inserted the paper clip about an inch or so in. Felt a little resistance when first going in. So hopefully in two weeks when the boat is in the water I will know the results. As others, I use the GPS for actual speed data, but like to see the instant MPG reading which of course doesn't work if the speedo is not working. It is a lot easier than reading the GPH and doing the math. Thanks again.

As least NY is letting us get 2 - 21" flukes during May. Better than postphoning the entire season.
 

georgemjr

Well-Known Member
Joined
Jan 2, 2009
Messages
441
Reaction score
38
Points
28
Location
Bay Shore, Long Island NY
Dunwurkin: that is my point. You are able to connect the gps information to the fuel management system so that it figures out your mpg with perfectly accurate gps speed rather than sometimes accurate pitot tube speed from the speedometer.