Search results

Had a Grady White factory tour back in Nov. staff admitted it is coming and will be introduced in 23 at a FL boat show. Not much detail but will have a port side fold down platform door. Hope it will have more fishing features IMHO the 251 CE is big on creature comforts too crowed for fishing &...

Had a hot short in my 23 Gulfstream perko It was set to off and while winterizing the motor my wrench hit the starter power and blew up the ecm. Replace the selector with a Blueseas switch screw holes may not line up but they make a much better product.

Before you dig into the display side remove the connector at the sender and short the 2 pins if the gauge reads full then you'll know the display is fine and the sender needs to be replaced. BTW you have to turn on your water pressure switch to supply power to the tank indicator.

Are you talking about the new CL5 display? I have one hooked to a MEC F150 via NEMA 2k cable to yami white 4 pin plug at the front. It's not CLP but was able add both a water pressure and Speed sensor to the motor and get it to display. To change one of the read outs just press and hold on one...

Pretty happy with my minn kota works well in 3' seas agree wind can push you more than waves use on allmost every trip out when btm fishing. here is the build. switched from the MK supplied over the top strap stabilizer to the Ram mount much easier to use with the PoppTops.com cover...

Take the small angled starboard off where the panel wall meets the ceiling its pain to reach but u can unthread the large back nut that holds the gauge to the wall. I could not get to the connector but there was enough wire to pull it out from the wall.

I had a 232 with a single 250 it was underpowered esp in rough seas trying to stay on top of the waves go w 200’s if you can find/afford them they weigh the same as 150’s and you wont have to run as high rpms for same speed

Just so others searching for this sender can find it thought I would share the part source. It's made by KUA Model S3U Sender it has a 1.25″ BSP Mount - 15" × 1 Looks like it is all SS now with no plastic blue cap. https://kus-usa.com/product/s3u-sender/?attribute_pa_length=15

Having a similar problem on my 04 300 Marlin checked the gauge by shorting black to blue it read full looked at the sender and it completely fell apart any idea where to find a replacement? There is a number on the blue plastic cap WU-15 83 think the tank holds 32 gals in the GW parts manual I...

Item is sold!

Thought I’d post another pic with it all put together will report back may have a sale pending.

Would these fit in a 2004 300 Marlin? My post measure 2 7/8” also are there nylon bushing insert for the spider that clamps to the post?

These are still available if anyone needs them send me a pm

Thought I had to and bought the 1” hinge/clasp which are now for sale on the wanted/sale forum. The Marlin rail extends forward enough of the pulpit to let it clear sideways during deployment. https://www.greatgrady.com/threads/1-bow-rail-hinge-latch-for-trolling-motor-deployment-for-sale.34474/

I purchased these items for a trolling motor installation but ended up not needing them spent around $150 for these parts will take $100. FYI the hole on the male clasp needs to be drilled out to 3/8" for the pin to fit.

Thought I would follow up on this old thread I started and share my TMsetup. After waiting a year for a 36v Minn Kota Terrova 87” shaft trolling motor and looking at various angles and options including the Shuttle Slide I went this route. In the vertical position the MK shaft has to extend 1.5"...

I'll have to measure what I have left I messed up a sectiion below the helm need to redo that and will let ya'll know what lenght remains

Hey @FLWhaler just sold 20’ to @SMNJ on this thread have another 20’ if u still need it same deal $60 plus shipping just pm me your address & email will send u an invoice.

Hey FLWhaler yes I do have a bunch left over how much do u need? Most Gradys take a bit over 20’

Hi @fishtails I’m looking to replace the seats on my 04 Marlin what model is your Lebroc chair, did you buy direct and what it set u back? Did it come w the spider and fit right on your existing 2-7/8” post? TY Mike