Search results

@Bayhouse how did you make out refinishing your floor? Restoring an 04 Marlin and looking for steps and materials to use to get this back in shape. Thanks Mike

Having a hard time finding an exact fit replacement microwave for an 04 Marlin. The old one is a Samsung MW640BA and measures 18 1/8" W x 9 3/4" H x 12 7/8" D. There are many .7 cf Microwaves out there but the hight is the problem as the walk around limits the clearance to under 10". Any...

I’m restoring an 2004 Marlin which has a few electrical gremlins. One of which when hooked to shore power the panel reads around 60-70 volts a/c but if I put a volt meter on any outlet it reads fine at 120v. This is on the shore power side I wont share the generator side issues yet. Thanks for...

I just Purchased an 04 Marlin with a leak on the Port side window over the galley. It must have been leaking for many years as it ran down the window shelf dripped on the microwave rusting it completely and also rusted the Isotherm 49 fridge/frame. Looks like it is coming from the mid bottom...

Hi Magicabill I like your approach and diligence. I just picked up a new to me Marlin with a serious mold problem what dehumidifier have you found to work well in the cabin & helm? Assume it's driven by A/C. Thanks Mike

Great info thanks so much for sharing! As soon as it warms up a bit here in NC I will be trying your approach.

Hi Capt Overkill would you be willing to share your tips to the great grady group on how you removed and applied your trim? Thanks

It Arrived today and I have a buyer for half the roll.Thanks for the interest.

I found several threads about replacing the Vinyl cockpit trim on gradys the source is Barbour Plastics and the link is https://www.integritymarinecorp.com/product-page/f8252 Since they only sell it in 105' lengths would anyone be interested in splitting it with me? The total with shipping to NC...

Is this the same trim that Barbour Marine sells for $2 a ft? unfortunately you have to purchase 105'

In process of purchasing a 2004 Marlin Motors are new 300 yamahas the hull is solid but needs a lot of TLC. Any one have a line on a replacement lid pn 10-947 for the Cutting Board – Stove Top lid? Have a note into Marine Connection Liquidators and will try GW parts but don't have much faith in...

Looking at a 2004 Marlin and the hull side pin striping and decal need to be replaced after some gelcoat repair. I can find the stern hull side decal on EBay but can't seam to find a source for the Navy/Gold stripe. Have you guys found any sources for that?

g0tagrip Where would you place the Zincs? If you have a pic could you share it? Do you think it necessary if I like magicalbill am as obsessive leave lift out of water when underway and rinse it after use?

Pressed the On button but hours did not display. Did some research which seems to point to the timing clock installed behind the control board. FP has a real bad rap on THT so not sure it is worth spending any $$ on it if not needed for overnighters.

Thanks No Bail that makes perfect sense when I tilted the wheel up it got even stiffer and squeaked more. I'll be back on the boat tomorrow and will report back here.

Thanks Fishtales will be on the boat tomorrow and will check that out

Could you share more details on maintaining winterizing the fisher panda generator on a GW Marlin? Can you flush it with fresh water after use? Do the same to pull in antifreeze? do you defog a diesel engine to winterize it? Owner says it runs but does not show hours on breaker panel so looking...

I am looking at a used 04 Marlin with fairly low hour 300 Yamis on it and was surprised by the way it swayed on plane especially when crossing wakes and waves parallel to the beam. Is this normal for the Marlin? Also the steering was fairly stiff and the wheel squeaked when turned. (no power...

I spoke with Mary at Rhodan she shared a few ideas on how some customers have mounted by the bow pulpit. The hinging SS rail is cleaver. Agree the 96" shaft would work best just not sure where the long arm will go in the stowed position. Wait time is almost a year for the 96"er

In the market for a used 30’ Marlin and have been wondering if anyone has successfully rigged a trolling motor on a marlin for the anchor lock feature to bottom fish? If so interested in any info & photos. Thanks Mike