Search results

Try RV curtains on Amazon or google

Mine are the far left. Red. The diffuse light from under them is not bad. The red is not terrible. But a dimmer would help. I drive for hours in the dark There is no way to dim the dependent lights because they use the 12v that is being sent to your devices

I was not suggesting fusing the Nav/Anc separately from the switch panel. That would cause complications with using it to light the other switches. New Wire refers to illumination lamps as "Independant", meaning they are powered independant of switch position. "Dependant "indicate ON and are...

I have red and still wish I had a dimmer. Sometimes I put my hat over the panel You have to pay attention to the type of switch for Nav/anchor if go with dimmer.

A few days ago I bought a CHEAP set of 4 blue LED that LOOKED like replacements for the OEM Attwood cockpit lights. Screws smaller and holes not as far apart and the unit will not sit flush against the gelcoat. The gasket supplied was useless. I will have to make neoprene washers or...

was the water pump off when you bubble tested?. Gotta take it apart and spray on the seals.

did you replace the fill gaskets every time? They get a ring when you tighten them and then if you use them again the ring is in a different place.

Lets tie 'er up & kick back some cold ones....

Can't help you. When I bought mine there was just a shaft from the motor and some holes with silicone. I pulled the motor and tossed it. Filled the holes with epoxy. Never looked back.

this looks like the original Must be made of Platinum based on the price... https://www.westmarine.com/ambassador-marine-shower-mixer-faucet-combo- This is more my price range ...single cold water www.amazon.com/Ambassador-Marine-Trinidad-Collection-Chrome

Do you have hot water? Are you ever going to shower? You could get a simple single valve faucet. Let me know what you find cuz I’ll be looking too they come out by turning the nut on top where the hose goes through

I used our big front loading washer. Tumbled on low,took out still a little damp. One zipper didn't make it

Yes probably ground for SSB

see this post. You would have room for bigger batteries. https://www.greatgrady.com/threads/new-battery-config-for-265.25744/ This is my new setup. Four batteries. One 24M starting battery for each motor and a parallel pair of 24DC as the house. The House charges from the AUX charging cables...

get the ones with the clear bowls. Racor 3213 or 3214 or equivalent. Be careful. There are two sizes of thread out there. I think Mercs oem bracket was different than Yammie,Zuke,Honda. Thing is..is doesn't matter what engines, someone may have replaced the bracket (aka manifold aka housing)...

OH! you have the old Euro Oval switches. YES. join the 21st century and get etched illuminated Contura switches FYI, the euro switches were slightly narrower that the Contura. You may not fit 6 across on the same size panel and into the same cutout in your dash. Measure 5 times, use their...

As I said before , been decades since I re-pinned molex connectors. In my early life I have done it quite often. You really need the stripping and crimping tools..and eyes...and patience. As you say, they crimp the wire and they crimp the insulation. The stripping has to be exact. You cannot...

I’m using the original Lee Jrs with 18ish foot aluminum poles. I added rollers I use 400#mono. I think if you go with longer aluminum poles you’re gonna need to put at least a single spreader kit on each. I don’t know how the carbon fiber ones stack up. I don’t have that much money ha ha We run...

fantastic.

Yep that bottom picture is grady tapping grounds off the larger black wires. The black wires on the switches have nothing to do with the circuits. They are only for the illumination of the switches. So the + wires of the circuits come from the switches and the grounds are "out there somewhere"...