Search results

2004

These guys install all the thrusters @ the GW factory https://www.floridabowthrusters.com/gallery/nggallery/page/1

Speaking as a huge GW fan owning several GW offshore boats If fishing is your priority on inshore and want to chase reds in shallow waters the CEX has too much draft, too many creature comforts & not enough fishing features for me. Small livewell under seat imagine the mess putting a castnet of...

My 2004 300 Marlin have to Trim the Starboard tab down 2-3 I believe it is the 4 batteries under the back Port box

Winterville Machine Works makes them for GW they have all the templates way back when they shipped me a top for may new 90 232 Gulfstream in 92

Instead of paying $40 for a new back up sender you can use a 240 ohm resistor for a few cents which is what a sender reads when tank is empty. Conversly it will read full at 30 ohms and ½ a tank at aprox 135 ohms. I used a resistor to determine the tank numers pin outs on my CL5 as cables were...

Hi there I ended up getting the smeta .7 cf microwave from amazon for $75. Had to cut a new starboard front face and foot holding board for the base but it fit fine and the cord was long enough. Amazon doesn’t list it anymore but can be found elsewhere...

Just to follow up the GW pn is 10-152 Taylor marine in DE has them on eBay for $27 ea their prices are a rip off so I ordered from my local Radio Island dealer for $6. Couldn't find the OEM part there are knock offs on amazon but harder plastic and not as tall

Hi @RobboNJ looking for the same clip mine broke while cleaning up after a fishing trip yesterday. Could you share that link? ty Mike

there is also a yellow wire inline fuse in the gauge cluster that could be dirty/blown I had a short in the CL+ bus that blew this fuse. gauge wouldn't come on but motor ran

Had a 90’s 23 w an outdrive and a 250 SW series 2 banger. With the wider beam boat was sluggish when in rough seas 4-6’ it was hard to stay on top w one motor. my advise would be to go w twins. Also don’t expect ti have any control w a single screw in reverse on a bracket.

I ended up buying these which I understand are the current year model seats. again no GW logo but almost $2k cheaper ea than what a GW dealer will sell them for w the logo. https://www.llebroc.com/product-p/4bmk3001.htm

Hi @glacierbaze I’m located near HI pm me and can give you my phone # and address if you want to come see them. Looking to get $400 for the pair. Mike

Just posted a pair here https://www.greatgrady.com/threads/2-pompanette-ladder-back-chairs.35927/

For sale are a pair of 2004 Pompanette ladder back seats with new cushions and arm covers. They came off a 300 Marlin and fit a 2 7/8" post. Also included is one post that can extend from 8-11". Willing to ship if freight is covered by purchaser. $400 SOLD!

Hi Joe the hawse was part of the original bow pulpit from Grady. You could call their parts dept for details on a source. Mike

@Harrysea I also have a Marlin what size screens were you able to get in there? I have a 12" and 7" furuno over black starboard Doesn't look likeI could squeeze two 12" displays in there. Thanks

I agree looks aftermarket open the panel and follow the wires. I found many 1/2 way done or vacant wiring from 2 previous owners on my 04 marlin. Pulled out everything that went nowhere

Hey Reeling ended up rigging the Marlin I bought in 2019 this way works great. see end of thread https://www.greatgrady.com/threads/rhodan-on-a-gw-marlin.31320/#post-236385

All the things mentioned esp VST are good to check along w measuring pressure on the rail. Also pull your injectors and have them cleaned by a pro they can print out performance before/after mine was down 30% on a few.