Search results

I have similar setup only Islander. The ProFish is mounted on my anchor rope locker. It works ok but be careful that you don't rip it out. Did that once and had to rebuild. Problem isn't where it's mounted. I had lots of problems with getting the windlass to swallow the 8-plait rope to chain...

More useless speculation. How many Angeles are on this pin head?

So what do you know about them?

I hate Srius XM. Almost free and overpriced. Good answer. I'll never understand why it's so difficult to charge a battery. Two pages of solutions to a simple problem and stupid mistake.

Removed mine. New one on the shelf. Tire of the rust staines.

No.

Are you on shore power? Do you have a charger? If not the ProMariner ProSportHD 20 is a good choice. The engine is capable of charging the battery it is connected to. But it takes hours if you really killed it. One running set 1 to #1 and 2 to #2.

This really is a simple job. You need to find someone who has experience sewing Makrolon. This is a rectangular piece that can be curved, a borders, keder awning and zippers. Track top and bottom. The problem is it is a small job. Where do you do your boating?

Your boat would be a little different. Mine snaps down to the windshield as did my old enclosure. I have a zipper attached to the keder awning rail in the original track with a zipper. I didn't need the zipper because of the snaps. In your case you should have keder awning rail top and bottom...

The pictures above on post #5 are of the 8612xsv. The 8610 is in overhead box and mounted on a bracket - not flush mounted.

Makrolon polycarbonate 40mil was $100 for a 4x8 sheet. I haven’t brought it lately. If the shop can’t wrap the corners then make a separate piece and zipper vertically. The front piece should be track top and bottom -slide in on bottom and zipper across top. Use Stamoid for borders.

Not sure on price. I do my own work so I can’t give you a price.The material can be curved. Bending is complex involving heat and a jig. Not something a local fabricator would tackle.

The 8610xsv is a much better unit. It has the higest resolution of all the 86xx series and significantly better than 1242/1243 display. Last year I swapped my 943xsv for a 8610xsv. 8610xsv $2,699.99. physical 10.25" x 8.0625" x 2.95" (25.9 cm x 20.5 cm x 7.5 cm). 6 15/16" cutout height screen...

Get a new polycarbonate windshield made. They only last a few years. The UV takes its toll. On my 268 Islander I have a one-piece full width polycarbonate panel. I have side panels that we can put up if needed but usually run without. Took the wipers off the glass windshield this year. Didn't...

Where are you? Type of use for the boat. Fisherman? Light duty or serious? 1997 268 Islander. I'm all Garmin. Everything good! 8612xsv, 8610xsv, GMR 18 Fantom Radar 40W, GPS24xd, Fusion MS-RA770. Garmin Navionics Vision+ charts. Florida sailfishing. We use the Furuno equipment on the...

Height the same but width is 2" less. 1243xsv is $2,899.99 physical 12.1” x 8.9” x 3.2” (30.8 x 22.8 x 8.2 cm). 7 15/16" cutout height screen. 10.3" x 6.4"; 12.1" diagonal WXGA; 1280 x 800 pixels Took to black door off and did a flush mount with hidden screws from behind. I did have to trim...

Probably was balsa. Although there was a significant amount of glue that leaked out. The black mold and sticky film was on my tanks too. When I pulled the hatch and stood it up it leaked coffee colored ooze out!

I frequently have no-flow out of tell tale port in my driveway. My mechanic said this is common with ear muff's. He suggested a "Y" hose connected to muff's and the engine flush hose. Works fine in the water. I keep a 2' piece of 300lb mono handy when I Spring launch. Sometimes the fuel cooler...

Now just imagine what those tanks look like on the bottom!

Fiberglast.com is a good source for materials. MESCO marine supply is good for Coosa board but you have to deal thru a marina - no retail. Marine plywood is fine to use. It uses a water resistant glue vs regular plywood. Use a slow hardener for the epoxy. West System 105 resin and 206 slow...