Search results

Lot of pumps now have a second outlet, which lets you add a second pump with one thru hull. The outlet is before the pump...

I did the same thing the OP is considering on my 22 Tournament, in a similar space behind each jump seat. I have a low bridge between my slip and open water, and can't start off with rods in the arch. Works great. IIRC, there was wood under that fiberglass, but I may disremember incorrectly...

When I can't see in a space, the first thing I do is to stick my phone in there and start shooting photos. Looks like you has access from the battery compartment, and from the hatch to port. There might also be enough slope to that seat backrest to allow a 15* rod holder, unless you just want...

What mounting holes were used on the twin set-up? If they were high, and you set the single low, you are probably okay. Water rises off the transom, and the longer the bracket, the less depth you need for the prop setting. There is a formula somewhere that shows the ratio of setback to engine...

I don't think that he wants to look over it. Like a lot of us, he would like to stand, look thru a clear windshield, with a good wiper, and not have his face in a 40 mph wind for hours at a time. Not something many builders offer in the under 30 size of boat. Having the ability to fabricate a...

Raise your existing windshield by adding a 4 or 5 inch base under it.

A rolling stone gathers no moss.

A call to GW tech support will probably answer your question in short order.

Somewhere in my memory is a, “fit to screen” key, maybe one of the F keys on the top row.

https://www.google.com/search?client=firefox-a&rls=org.mozilla%3Aen-US%3Aofficial&ei=EvK0W5L1F-SOgge997bYDA&q=MM+Marine+in+Baltimore&oq=MM+Marine+in+Baltimore&gs_l=psy-ab.12..0i22i30.2671.2671..4385...0.0..0.87.87.1......0....1j2..gws-wiz.......0i71.yBo_qBhtlT8

I need two ball and socket type, preferably with the teeth on the mounting brackets. Mine are 9 and 19 inches, outside of ball to outside of ball. Does anyone make a cut-to-fit kit?

I have the canvas on my '93 Tournament, but it was designed by a moron. It zips open from the bottom, so that you would still have to get on your knees and crawl thru, since it does not separate at the top. It should zip down from the top, so that you can step thru. For the stbd channel, take a...

What's the over and under on what they cost from Grady White? I'll guess $1,000 for the set.

I'm not that smart, but I think those hydraulic lines stay full in both directions, all the time, like a brake line. So the fluid doesn't travel from the helm to the tab, every time you move the control. The pump moves X amount of fluid into one end of the line, and the tab moves a corresponding...

If the power from the panel just splits off to the pump, them the pump would run constantly when the switch is on, even when the AC is turned off. Pump has to be activated either by the thermostat, or by a switch on the AC. Stick your phone in there and take some photos of the control unit...

Fresh water lakes, or saltwater? Go into your cp, and put your location in so that people will know what area you are in.

Since it is already wet, I would probably hook it to the truck, disconnect the bilge pump, and put 50 gallons of water in the bilge, and drive it doing a lot of stops and starts. Drain it out, and repeat a few times. Maybe even get a rotating sprinkler on the end of a hose, and shove it into...

Are you sure that you don't have a separate breaker on the electrical panel for the pump?

My biggest concern, when I have my boat winched tight to the post, is that the latch will slip, and the handle will take some part of my head off. My winch is one where you can slide the handle out of gear, and I try to always do that anytime my hand is not on it, like dealing with the safety...

Google pleated marine vinyl.