Search results

kind of makes you wish you didn't cut them?

5/8 is a pretty hefty line even for a 330... I would think. The WM brand and the NE Ropes are both good when you get them on a big sale.

I hooked up the Garmin 1242 and updated to the 1/2023 latest I don't think the update changed any of my custom data bars The Navigation bar is a special function. It can be set to auto. That will make it appear when you are "navigating" to a Waypoint (GoTo) or a Route The 4 things in the bar...

heheh so it begins... That Marlin will have you blowing past breaking bass on your way to overnighting in Wilmington canyon. You need some 80Ws for bigeye....

Is that a change in software or was it always that way? Sounds familiar. Is that a new software 1/2023? or the one at the end of last year? I'll have to set mine up and look at it again. I pulled the dash from the boat. I have a spare Garmin power cable... connect to a jump starter. Sit in...

yep. better than trying to solder on lithium batteries.

I hear your frustration. I realize you have done troubleshooting and you are just are asking for someone with the same boat and same transducers to tell you where they put theirs. You don't want to cut new giant holes in your boat if it isn't going to fix the problem. I don't have that boat and...

I have an ACR PLB-375 from 2017. The battery was about to expire and the NOAA registration was due. I decided to replace the battery myself. Exact replacement on https://beaconbatteryreplacement.com/product/acr-plb-375-resqlink-battery/ was $40 Simple job. Two screws. One of the philips...

"I have turbulent interference on my thru-hull transducers (B175’s)' You have two transducers? one's a 50Khz. There is one on the other side? 200Khz or 150khz? Both do the same thing at the same speed? They are brand new transducers? New Sonar? Which one? Have you ruled out low power from...

Just finishing up this project started in December. 1985 Sylvan 16 that we've owned since '88. First boat. The original "SkunkBoat". This boat has been from Canada border to Sambo Reef off Key West. This is the second time replacing main deck. Third paint job. The Tohatsu 40 finally gave out...

I have used D-cross section neoprene foam weather stripping...Amazon

Raising the motor into higher holes effects the RPMs and could possibly cause the props to suck air. When I had Yammy OX66s the Lower units touched the water. I tried Trilux, West Marine brand outboard antifouling spray, and Hydrocoat Eco. they all worked ok. The Hydrocoat looks the best...

How much do you use the boat? Where do you use it? Lake, Bay, Coastal/inlet, Far offshore? That is a mitigating factor. If a motor dies in the bay, you putter home on the other one and get it fixed.... How long are you going to try to keep them running? Salt water boat? It could need engine...

https://www.greatgrady.com/threads/deck-hatch-re-core-265.32638/

My first reaction is that a power connection problem would cause the unit to reboot and also give you a low voltage error. The picture points me to a bad unit. The screen is not scanning correctly giving you a doubled picture.(or its "rolling" vertically) And you describe it only after running...

I don't think any Gradys came standard with a ground plate. Not necessary unless you have a Single Side Band radio

heheh I meant the OP.

I think he's talking about the vent for the generator space, not a window/vent. It is thru the balsa core of the hull, under the rub rail of the gunnel. The bigger Gradys have balsa cored hull sides, sold glass bottoms.

Not familiar with the 330 wire routing but consider running a 2k backbone up to the top rather than a drop. That way you can eventually add more drops up there without more wires.

yep as I said preferable solution is an isolated House bank.. Did you look thru the 265 battery config thread? I know the boat layout is probably a little diferent than yours but the setup does exactly what you are looking for and it incorporates the existing switches and wires. Look at the...